Senior Instrumentation & Controls Engineer at Sterling Oil Exploration and Energy Production Company Limited

Sterling Oil Exploration & Energy Production Company Limited (SEEPCO) is an indigenous company that ventured into Exploration and Production (E&P) business in the year 2005. SEEPCO participated in the 2005 bid round held by Department of Petroleum Resoucres (DPR) and was successful with license OML 143 (formerly OPL 280).

We are recruiting to fill the position below:

Job Title: Senior Instrumentation & Controls Engineer

Locations: Lagos & Akwa Ibom
Employment Type: Full-time
Reporting to :Project Head (CPP)/ Engineering Manager (Lead) / Construction Manager

Job Summary

• This position will be responsible for a Design and Engineering work, planning and overseeing installation,Testing and Commissioning, Operation and Maintenanceof all systems related toCombined Cycle Power plantunder general supervision.
• Preparation of Instrumentation Specifications, Philosophy, Lists, Requisitions, calculations, schedules and drawings for procurement, installation and commissioning of installations (Brownfield and Greenfield Projects) for Conceptual studies/Basic Engineering, Front End Engineering design (FEED), Detailed Engineering Design (DED) Projects.
• Must have Gas based Combined Cycle Power Project experience.
• The Instrumentation & Control system in CCCP shall consist of:
  • GTG Control system (SIEMENS T3000 or GE MARK Vie or other OEM equivalent)
  • STG Control system (SIEMENS T3000 or GE MARK Vie or any other STG OEM)
  • DCS Control system for complete CCPP (Yokogawa, Honeywell, METSO, SIEMENS, GE MARK Vie or equivalent)
  • PLC’s of different BOP packages
  • Field Instrumentation for GTG, HRSG, STG and BOP.

Main Duties

• Expertise in Design & Engineering, Engineering review and Comments, Installation supervision, Testing and Commissioning, Trouble shooting and O & M of I & C system of Combined Cycle Power plant.
• Supporting all the phases of project cycle from Concept, Design and engineering till Operation of complete Combined Cycle Power plant where little evaluation or ingenuity is normally required.
• Ensure that designs comply with the relevant procedures, standards and regulations.
• Review of Instrumentation drawings (location drawings, interconnection drawings, cable termination drawings, cable tray/route drawings, cable block diagrams, control system block diagrams, shutdown logic diagrams, function block logic diagrams, hook-up drawings for various instruments, layout drawings, junction box termination drawings, level coordination sketches,).
• Ensure, as far as practically possible, that all assigned work is carried out in compliance with agreed budget and schedule.
• Prepare/Review of control philosophy, P&I diagrams, cause & effect diagrams, instruments list, flow chart.
• Keep up to date with technical developments, National and International standards and legislative requirements related to the discipline.
• Familiar with International codes, Standards and recommended practices for design and selection of I & C as described above.
• Prepare specifications for floating RFQs (instruments, control systems, control panels).
• Prepare engineering calculation spreadsheets.
• Takes entire responsibility for the execution of detailed design and ensuring compliance with the project specification.
• Should be familiar with interlocks and protection - wiring and instrument signals and drawings for both simple and combined cycle.
• Liaise with other departments, clients, vendor, subcontractors, third parties and approving authority.
• Participate in inter-disciplines, project, client, vendor, subcontractors and third parties meetings.
• Participate in design review such as HAZOP, SIL classification, Independent Design Review Constructability review, P&ID review and 3D model review meetings.
• Perform Inter-discipline check and Job assignments.
• Perform Instrumentation engineering review activities on documents/drawings produced out by other Engineers, Designers and CAD Operators.
• Prepare scope of work, man-hour and cost estimates for proposals.
• Provide professional advice to peers in Instrumentation engineering design.
• Coordinate with clients, contractor and consultants to determine project requirements, schedules and deliverables.
• Support design engineering responsibility and supervise work done by Installation and Testing technicians during project execution.
• Specify and set the standards for HSE requirements for I & C system of CCPP.
• Prepare estimates and schedules and assist in their review.
• Encourage and provide lateral learning within the project.

When at site:

• Co-ordination with clients, consultant, contractors throughout the entire Projects development
• Phase, attending meetings.
• Supervise Erection of assigned subsystems and also getting involved in commissioning activities to ensure system is fully and safely operational as per design.
• Report any anomaly or deviation in the construction document which can jeopardize the safety and functionality of the sub system and plant operations.
• Ensure MEI contractors properly update the drawings, marking as red-correx so a proper as-built is available at the end of the project.
• Read and interpret drawings extracting relevant instrument engineering information required for Erection, Installation, Pre-commissioning and Commissioning.
• Participate in meeting with contractor’s supervisor to review drawings for scheduling and assigning work to keep up the project schedule.
• Supervise and Guide Contractor’s Supervisors for executing the work in Planned and systematic way.
• Involved in Instrument Installation, Calibration, Cable Laying, Termination, Calibration and Loop checking.
• Coordinates with operations and safety personnel to obtain work permit for planned work to be carried out during Commissioning Stage.

Requirements

• Bachelor's Degree in Electrical / I & C Engineering.
• 15+ years’ experience in the power plant projects with specific experience with combined cycle gas based power projects.
• Readiness to be at site based in Akwa Ibom, Nigeria as per project requirement.
• Ability to work efficiently and effectively when managing multiple tasks.
• Effective oral and written communications and excellent interpersonal skills with the ability to deal effectively with the design team in the resolution of project related issues.
• Must be self-motivated, results oriented, and be flexible to work well under tight schedules in a fast paced multi-disciplinary team environment.
• Candidate should be competent to work with any GTG control system of any reputed OEM for Large Frame gas turbines + any of reputed DCS Manufacturer.
• Should have complete understanding of process ladder logics and its interconnections.
• 5+ years in engineering of power plants in I & C
• Preference shall be given to candidate with previous experience working for the Owner, Consultant or EPC contractor on large CCGT projects.
• Readiness to travel

Remuneration
N500,000 Monthly.

How to Apply
Interested and qualified candidates should send their CV to: [email protected] using "Senior Instrumentation and Control Design Engineer" as the subject of the mail.

Application Deadline 29th September, 2023.